• Производитель
    0
    0
  • Наличие
    0
    0
    0
    0
    0
КАТЕГОРИИ

Ремни безопасности

Ремни безопасности
На странице:
Сортировка:
The FORMULA 6 is a 6 point FIA approved harness for reclined or space limited seating positions as found in various formula cars, prototypes and kit cars. The routing of the crotch belts is through D-Rings on the lap belts so there is no hardware between the legs of the driver in the small confin..
$495
The FORMULA 6 is a 6 point FIA approved harness for reclined or space limited seating positions as found in various formula cars, prototypes and kit cars. The routing of the crotch belts is through D-Rings on the lap belts so there is no hardware between the legs of the driver in the small confin..
$495
The FORMULA 6 HANS is a 6 point FIA approved harness for reclined or space limited seating positions as found in various formula cars, prototypes and kit cars. The routing of the crotch belts is through D-Rings on the lap belts so there is no hardware between the legs of the driver in the small c..
$525
The FORMULA 6 HANS is a 6 point FIA approved harness for reclined or space limited seating positions as found in various formula cars, prototypes and kit cars. The routing of the crotch belts is through D-Rings on the lap belts so there is no hardware between the legs of the driver in the small c..
$525
The RACE 6 HANS is the same as the RACE 6 but with 3" to 2" shoulder belts that are compatible with the HANS® device and other head and neck restraints. The lower section of the shoulder belt, including the adjuster, is 3" while the upper section of the shoulder belt, where it passes over the hea..
$455
The RACE 6 HANS is the same as the RACE 6 but with 3" to 2" shoulder belts that are compatible with the HANS® device and other head and neck restraints. The lower section of the shoulder belt, including the adjuster, is 3" while the upper section of the shoulder belt, where it passes over the hea..
$455
The RACE 6 HANS SFI is the same as the RACE 6 but with 3" to 2" shoulder belts that are compatible with the HANS® device and other head and neck restraints. The lower section of the shoulder belt, including the adjuster, is 3" while the upper section of the shoulder belt, where it passes over the..
$495
The RACE 6 HANS SFI is the same as the RACE 6 but with 3" to 2" shoulder belts that are compatible with the HANS® device and other head and neck restraints. The lower section of the shoulder belt, including the adjuster, is 3" while the upper section of the shoulder belt, where it passes over the..
$495
The RACE 6 SFI is the premium harness for your competition vehicle if you require SFI certification or if you prefer 3" lap belts. This 6 point harness is both FIA and SFI 16.1 certified with T-Bar sub-strap, 3" shoulder belts, 3" lap belts and the exclusive TAKATA aluminum multi-point release ca..
$475
The RACE 6 SFI is the premium harness for your competition vehicle if you require SFI certification or if you prefer 3" lap belts. This 6 point harness is both FIA and SFI 16.1 certified with T-Bar sub-strap, 3" shoulder belts, 3" lap belts and the exclusive TAKATA aluminum multi-point release ca..
$475
Replacement or Additional Anti-Sub Straps for your TAKATA Race 6 harnesses. Available in Black or Green. ..
$95
Replacement or Additional Anti-Sub Straps for your TAKATA Race 6 harnesses. Available in Black or Green. ..
$95
Standard 3 Bar Slide for 2" webbing. Uses the simple 3 Bar Slide wrapping technique. Most commonly used for HANS specific shoulder belts or anti-sub straps.If you are running in an SFI 16.5 series, you need the LV11NC. ..
$10
This 3 Bar Slide is designed to be used to wrap any 3" webbing to a harness bar, or to wrap any end fitting into a 3" piece of webbing. This is the bracket found on all 3" shoulder belts.Uses the simple 3 Bar Wrapping technique. If you are in an SFI 16.5 series, be sure to select the LV7NC o..
$10
This kit is to be used in conjunction with the Snap-On end fittings on Takata Harnesses. Use this bracket to bolt into a hard to reach place in your car, then snap the harness on to it.Brackets are designed to be bent up to 90° in either direction. Do not bend back and forth repeatedly, as ..
$20
The B24 is the most economical bolt-in bracket offered. It is a heavy-duty Steel bracket that cannot be bent to aid installation. Dimensions are 5mm thick, 69x46mm with a 13mm (1/2") bolt hole. There is a slight 10° bend so that this bracket can be bolted directly to a fl at surface and leave ro..
$5
These Eye bolts are designed to work perfectly with the B14 Snap On Brackets. Offered in lengths and thread pitches shown. ..
$5
This Takata Reinforcement Plate is used for installing harnesses to the floor of your vehicle. This will provide a solid backing plate for eye bolts to mount to. Not required for all applications.  80 mm x 50 mm x 3 mm w/welded 7/16" nut. Use with Eye-bolts and/or 7/16" Bolt-In hardware..
$10
This Takata Reinforcement Plate is used for installing harnesses to the floor of your vehicle. This will provide a solid backing plate for eye bolts to mount to. Not required for all applications.  80 mm x 50 mm x 3 mm w/welded M10 nut. Use with Eye-bolts and/or M10 Bolt-In hardware ..
$10
This Takata Reinforcement Plate is used for installing harnesses to the floor of your vehicle. This will provide a solid backing plate for eye bolts to mount to. Not required for all applications.  80 mm x 50 mm x 3 mm w/welded M8 nut. Use with Eye-bolts and/or M8 Bolt-In hardware ..
$10
For use in installation of your safety restraints, additional eyebolts and eyebolt reinforcements are sometimes necessary when accommodating safety belt installation to frame/body of car. ..
$25